to washer or not?

Post your Misc Tech and Restoration Q&A's and general BMW queries here

Moderator: Moderators

fastdonkey
Forum User
Posts: 67
Joined: Sat May 28, 2011 5:03 pm
Country of Residence: united kingdom

to washer or not?

Postby fastdonkey » Tue Apr 09, 2019 3:54 pm

Hi all,

The question revolves around my 1952 Condor( side valve twin). The barrel, sleeved alloy, has six m10 retaining nuts. There are no washers
under the nuts on either side. I do have a schematic which does not show a washer under the nut. There is a little bit of 'graunching '
under a couple of the nuts which I am keen not to exacerbate.
So.......the question to the engineers/more technically minded among you is, do I put washers in ( don't think I have ever assembled anything
without one) or do I go with the schematic, leave without, and use a blob of locking compound ??

Regards, warner

User avatar
george baker
Club Member 14
Posts: 7273
Joined: Mon Aug 01, 2005 10:51 am
Country of Residence: uk
Location: Manchester,UK

Re: to washer or not?

Postby george baker » Tue Apr 09, 2019 6:06 pm

Hi
I almost always use washers, especially steel nuts next to alloy lump, better grip and no 'graunching '

George
Member 21, R100R, and an unused K75

User avatar
windmill john
Forum User
Posts: 3672
Joined: Fri Feb 18, 2011 9:58 am
Country of Residence: England
Location: Somewhere in Southern England. bip bip bip, loose lips sinks ships

Re: to washer or not?

Postby windmill john » Wed Apr 10, 2019 8:20 am

No graunching plus a slight spreading of the load too.
http://www.kittos.co.uk
Best roads: 623 Burgos to Santander. A back road to Metz; can't remember which!
Bumble, my 700 Transalp.
Gupta, my 350 Royal Enfield.
Sold my Airheads, what an idiot, but Honda is also great.
Too many bikes have come and gone, trying to be sensible now!

User avatar
P-K
Site Admin/Club Member
Posts: 2964
Joined: Thu Oct 07, 2010 5:33 pm
Country of Residence: England
Location: Darlington, Co. Durham

Re: to washer or not?

Postby P-K » Tue Apr 23, 2019 11:13 pm

I agree with both John & George.
Always use washers.
Phil,
'17 R9T Urban G/S : '12 R1200R
Site Administrator, Assistant Webmaster and Official Club Tweeter @BMRidersClub

King Herald
Forum User
Posts: 620
Joined: Wed Apr 05, 2017 3:24 pm
Country of Residence: United kingdom
Location: Midlands.

Re: to washer or not?

Postby King Herald » Wed Apr 24, 2019 8:13 am

Definitely use a washer wherever the surface is soft or uneven. And use a dab of oil, or Copperslip, depending on the location.
1997 BMW R1100R
1993 Honda Transalp 600

fastdonkey
Forum User
Posts: 67
Joined: Sat May 28, 2011 5:03 pm
Country of Residence: united kingdom

Re: to washer or not?

Postby fastdonkey » Thu Apr 25, 2019 1:36 pm

Hi guys,

Thanks for the replies. Everyone I spoke to on this made the same comments as voiced here.
No one could come up with a good reason for not using a washer under these circumstances.
Washers it is then, albeit thin ones as there is no 'extra' stud length to accommodate them.

Thanks again for the interest. Warner.

User avatar
DEEP DIVER
Forum User
Posts: 1792
Joined: Sun Jan 30, 2011 11:46 pm
Country of Residence: ENGLAND
Location: Felixstowe

Re: to washer or not?

Postby DEEP DIVER » Thu May 16, 2019 10:34 am

Washers all the time.
I tried to be normal once, worst two minutes of my life.
Blue belt in Serious tea drinking.

Barry the old goat!!!!
1985 R80ST being rebuilt #-o
1985 R80RT Touring dream :smile:
2 Harley sportsters being rebuilt #-o
And a VW trike so I don't fall off :shock:


Return to “Miscellaneous & Restoration Q&A's”

Who is online

Users browsing this forum: No registered users and 1 guest